top of page
Itzick Simon
English Logo

Safety in electrical work

Feb 15, 2018

Safety in electrical work

By: Asher Asban

The contractor’s works insurance policy you purchased, as well as the contractor’s liability insurance covering electrical work, is intended to serve as your safety net against claims or compensation for bodily and mental injuries. However, coverage is not automatic in every case; much depends on the safety measures or “risk mitigation provisions” included in the policy you purchased. Problems may arise if the required safety regulations under the law are not followed, or if you deviate from existing standards and procedures. Such deviations may create issues ranging from partial compensation by the insurance company to complete denial of coverage.


To draw attention to this, we present an article by safety expert Mr. Asher Asban on the topic of “Safety in Electrical Work,” which highlights and refreshes the key do’s and don’ts.


Incidentally, refreshing these guidelines is even more important in urban renewal projects requiring policies such as TAMA 38 insurance, because during electrical work, residents may be moving around the site. These residents are often unaware of the hazards, not familiar with safety regulations, and there is no practical way to enforce that they comply with safety instructions.

​

Safety in electrical work

"Safety in Electrical Work"*

Article by Asher Asban, Safety Expert and Construction Site Accident InvestigatorThis article does not provide safety advice to contractors, who must consult the relevant authorized authorities.


Many accidents occur due to a lack of awareness of the high risk posed by electricity on construction sites. This risk is particularly pronounced because installations and connections are mainly temporary, frequently assembled or disassembled on-site. Below is a set of general guidelines for performing electrical work and/or work using electrically powered equipment.


Any electrical work, electrical installation, connection, or loading of electrical lines—whether permanent or temporary—must be carried out in compliance with all relevant laws, including official standards, and according to any additional instructions in this procedure.


No person shall perform any type of electrical work unless they hold a valid license and are legally authorized to perform such work according to the type and scope of the work.

Live electrical work shall only be performed when strictly necessary and after obtaining a “Permit for Live Electrical Work.”


Employees are prohibited from working near unprotected electrical equipment, circuits, or any other electrical system unless these systems are protected against electrocution through grounding.


Work near active electrical systems must follow the site’s work and safety procedures. In the absence of such procedures, work may only proceed with the approval of the site safety officer.


Electrical tools and equipment must not be operated in areas or environmental conditions with moisture, high humidity, explosive dust, fumes, or flammable liquids, unless the tools and equipment are specifically designed for such conditions.


Panels, cabinets, junction boxes, or electrical boxes must be equipped with closures and lockable main switches. Construction materials must be non-combustible, and cabinets must remain closed at all times.


Employees performing electrical work or operating electrical equipment must avoid wearing rings, necklaces, bracelets, or any metal accessories.

Using extension cables:

Using extension cables:

Important instructions

  • The use of extension cords should be minimized and limited as much as possible and for essential and necessary needs only. It is recommended that a long extension cord that is in continuous use not be left rolled up on a drum to prevent overheating and the risk of fire.

  • Extension cables for use with hand tools and any other equipment will have double insulation, wires and a sheath (adapted for deployment and heavy-duty work – (Heavy Duty) on work sites and in field conditions).

  • Extension cables for use with hand tools and any other equipment will have double insulation, wires and a sheath (adapted for deployment and heavy-duty work – (Heavy Duty) on work sites and in field conditions).

  • Extension cord repairs will be performed professionally, with full restoration of the insulation and sealing (using heat-shrinkable insulation tape for sealing). Splitting and branching of extension cords is prohibited.

  • Powering electrical tools and using electrical cables on work sites in general and construction sites in particular requires ground fault protection for the power source. The circuit breakers on the power line will be of the magnetic/thermal protection type against short-circuit currents. The protections must be checked regularly and at fixed and planned intervals.

  • In any case of a circuit breaker tripping or protection activation, a qualified electrician must verify the cause of the failure, inspect and repair if necessary, and authorize restart.

  • Care must be taken to clearly mark circuit breakers and electrical power supply sources, especially when feeding from sources with different voltages.

  • Follow all safety laws and procedures for working near high-voltage lines. Working near high-voltage lines with lifting equipment requires the presence of a supervisor and/or a nearby lifter.

  • At a construction site, it is the contractor's responsibility to inspect and inspect, at a regular frequency and at least once a month, the sources of supply of electrical energy, electrical cabinets and junction boxes, circuit breakers, protections, cables and any other electrical equipment on site.

The test will be performed by a suitably qualified electrician.

The foreman will check the circuit breakers at least once a week.

Important Guidelines

  • Minimize the use of extension cables wherever possible, limiting them to essential needs. A long extension cable in continuous use should not be left wound around a reel, to prevent overheating and fire.

  • Extension cables used with handheld power tools and other equipment must have both insulated conductors and an outer insulating sheath, suitable for heavy duty use at work sites and in field conditions.

  • Extension cables used with handheld power tools and other equipment must have both insulated conductors and an outer insulating sheath, suitable for heavy duty use at work sites and in field conditions.

  • Extension cables must be repaired professionally, fully restoring their insulation and sealing, using heat shrink insulating tape to achieve a seal. Branches or additional connections must not be made in an extension cable.

  • Power supplies for electric tools and electrical cables at work sites, particularly construction sites, must have earth fault protection at the supply source. Circuit breakers on the supply circuit must provide magnetic and thermal protection against short circuit currents. Protective devices must be checked regularly at planned intervals.

  • Whenever a circuit breaker trips or a protective device operates, an appropriately licensed electrician must identify the cause, inspect and repair the fault as necessary, and authorize re-energization.

  • Circuit breakers and electrical supply sources must be clearly labelled, particularly where supplies operate at different voltages.

  • Comply with all applicable laws and safety procedures for working near high voltage power lines. Work involving lifting equipment near these lines requires a dedicated guide and/or signaller.

  • At construction sites, the contractor is responsible for arranging regular inspections, at least monthly, of electrical supply sources, distribution boards, junction boxes, circuit breakers, protective devices, cables, and all other electrical equipment on site.

The inspection must be performed by an electrician holding the appropriate licence.

The site manager must test residual current devices (RCDs) at least once a week.

​

​

​

​

​

​

​

​

​

​

Safety in electrical work

​

​

​

Safety in electrical work
Documents
Back
Safety in electrical work
bottom of page